🔒 Laboratory Authorization

Enter bench authorization key to reveal unannounced hardware prototypes and confidential schematics:

MONITOR & REFERENCE · 4U Rack Extension · Active Beta · v1.0.0
Touchstone Emblem

Touchstone

Master Reference Deck, 4-Band Solo Matrix & Binaural Control Room

Touchstone Front Panel HD RenderTouchstone Folded Front Panel HD Render
Touchstone Rear Panel I/O HD RenderTouchstone Folded Rear Panel HD Render

A Dedicated Control Room for Reason’s Master Section

Reason’s Master Section has never had a dedicated, non-bouncing Control Room bus: anything left engaged on your master chain prints straight into an audio bounce if you forget to bypass it before exporting. At the same time, comparing an unmastered mix at -14 LUFS against a commercial release mastered at -8 LUFS tricks your ears into favoring whichever source is louder.

I built Touchstone to sit in the final insert slot of your Master Section and handle reference A/B comparisons, loudness matching, frequency-band translation checks, and headphone speaker crossfeed in one 4U unit, while keeping your exported bounces protected.


In the Mix: Five Everyday Control Room Workflows

1. Loudness-Matched Reference A/B Without Volume Bias

Drag up to four full-length MP3, WAV, AIFF, or other supported audio reference tracks directly onto the Reference Slots (A through D) on the lower right (or patch live stems and rough mixes into the rear EXT REF 1 and EXT REF 2 stereo inputs). Touchstone runs a background two-pass ITU-R BS.1770-4 gated loudness scan on each file, displays its integrated LUFS and waveform, and trims reference playback automatically when MATCH is lit so your reference tracks sit at the exact perceived loudness of your live mix (guarded by a -0.3 dBFS peak ceiling so quiet acoustic mixes never clip hot masters). Click any REF A through EXT 2 button to crossfade smoothly into that reference over 10 ms, and click the active button again to toggle straight back to your live mix.

2. Comparing Sub-Bass, Low-Mids, Presence, and Air Side by Side

Judging whether your kick and sub sit at the right level against a reference track is much easier when the midrange isn’t distracting you. Click SUB (below 60 Hz), LOW (60 to 250 Hz), MID (250 Hz to 4 kHz), or HIGH (above 4 kHz) in the Band & Solo section, or click directly inside the four frequency zones on the spectrum display. Because the 24 dB/oct Linkwitz-Riley solo filters sit after the Mix/Reference switch, flipping between your mix and REF A lets you compare the exact same frequency slice through identical filter slopes.

3. Export-Safe Dual-Bus Monitoring on 4+ Output Interfaces

If your audio interface has separate headphone or monitor outputs (such as Outputs 3/4), patch Touchstone’s rear PHONES OUT L/R directly to Hardware Interface Audio Out 3/4 while leaving MAIN OUT L/R connected to your Master Section stereo return, and latch the armored SAFE button on:

  • MAIN OUT L/R stays locked to a bit-exact floating-point copy of your mix input (SAFE • MAIN BIT-EXACT), making it impossible to accidentally bounce a soloed Sub band, headphone crossfeed filter, or commercial reference track into your exported file.
  • PHONES OUT L/R continues to carry all active Reference A/B, LUFS Match, Band Solo, Mono/Side, and Crossfeed monitoring to your headphones or studio monitors.

Working on a two-output laptop rig without separate monitor outs? Leave SAFE off while mixing: Touchstone lights an amber SOLO / REF warning indicator whenever any non-flat monitoring state is audible on MAIN OUT, and latching SAFE before you export restores bit-transparent passthrough in one click.

4. Checking Headphone Mixes on Virtual 40°, 60°, and 80° Monitors

Mixing exclusively on headphones exaggerates hard-panned elements and hides phantom-center buildup because your left ear never hears the right driver. In the Control Room bay, switch from DIRECT to 40° (tight desktop nearfields), 60° (standard equilateral studio monitor triangle), or 80° (wide mains). Touchstone models spherical-head interaural time delay alongside a 700 Hz head-shadow contour while normalizing low-frequency sum gain so your mono sub-bass weight never shifts when toggling crossfeed in and out.

5. Timeline-Synced Arrangement Checks or Stopped-Transport Cue Loops

Toggle SYNC to match how you want to navigate your reference tracks:

  • Timeline Sync (SYNC On): Reference playback locks to Reason’s playhead position and tempo, so jumping to Bar 33 in your arrangement jumps to the matching timestamp in your reference track. Dragging the bottom Waveform Scrubber offsets the reference start point so you can line up song downbeats despite different intro lengths.
  • Cue Loop (SYNC Off): Loops the reference track (or your Sample Editor Play/Loop markers) continuously on its own transport, letting you scrub and audition chorus sections on the waveform even while Reason’s main transport is stopped.

Tactile Control: Front & Rear Panel

Upper Console Strip: Source, Band Solo & Control Room

Every radio button group on Touchstone uses click-to-toggle-off hardware behavior: clicking an unlit pill selects it immediately, and clicking the currently lit pill returns straight to your flat LIVE MIX, Full Range, Stereo, or DIRECT state.

  • Identity & Status Bay: Patch browser, 3-state OFF / ON / BYP switch, and the amber SOLO / REF warning LED indicating when non-flat monitoring is active on MAIN OUT.
  • SOURCE DECK: Six source chiclets (REF A, REF B, REF C, REF D, EXT 1, EXT 2, with all-off returning to LIVE MIX), paired with MATCH (automatic BS.1770-4 loudness matching) and SYNC (timeline lock vs. free cue loop).
  • BAND & SOLO: Four Linkwitz-Riley solo pills (SUB, LOW, MID, HIGH), four channel-routing pills (MONO, SIDE, LEFT, RIGHT), and Ø 180 polarity invert.
  • CONTROL ROOM: Armored SAFE master passthrough lock, DIM -18 (-18 dB talkback attenuator), headphone CROSSFEED selector (DIRECT, 40°, 60°, 80°), and calibrated LEVEL monitor trim (-24.0 to +12.0 dB).
  • Compact 1U Folded Strip: Collapsing Touchstone in the rack keeps OFF / ON / BYP, the patch browser, A / B / C / D / E1 / E2 source pills, SUB / LOW / MID / HI band solo pills, XFEED, armored SAFE, and LEVEL right on the 1U strip.

Lower Control Room CRT & Reference Cartridge Deck

  • 50 FPS Control Room Display: Overlays your live Mix spectrum (amber) against the active Reference spectrum (cyan) across 32 1/3-octave RTA bands divided at 60 Hz, 250 Hz, and 4 kHz, paired with top status banners (SOURCE, LUFS MATCH gain offset, and SAFE • MAIN BIT-EXACT), dual MIX / REF level bars, live Integrated/Short-Term LUFS and dBTP readouts, a -1 to +1 stereo phase CORR meter, and the bottom Waveform Cue Scrubber.
  • 4 Broadcast Reference Cartridges (A through D): Drag audio files straight from your OS or Reason’s browser onto any slot pad, or step through files with the dedicated Sample Browser buttons. Each cartridge displays the loaded filename and pre-scanned Integrated LUFS value.

Rear Audio & Control Room CV Matrix

  • 10 Audio Jacks: Auto-routed MAIN MIX IN L/R, two stereo external bus inputs (EXT REF 1 L/R and EXT REF 2 L/R), MAIN OUT L/R (EXPORT-SAFE), and PHONES OUT L/R (HW OUT 3/4).
  • 3 Control Room CV Jacks:
    • SOURCE (0-1V SEL): Stepped CV input selecting LIVE MIX, REF A through REF D, or EXT 1 and EXT 2 for hardware controller mapping or blind A/B sequencing.
    • BINAURAL (GATE IN): Engages headphone speaker crossfeed from an external gate or Combinator button without altering your saved patch state.
    • REF ACT (GATE OUT): Outputs a high gate whenever a reference slot or external bus is being auditioned (and drops to zero on LIVE MIX), useful for lighting rack indicators or muting auxiliary meters during reference checks.

Under the Hood: Zero-Copy Streaming & Phase-Pure Math

  • Contiguous Resident Sample Streaming: Rather than duplicating four full-length stereo masters onto the real-time audio heap, Touchstone pre-scans Integrated BS.1770-4 loudness and a 256-bin waveform overview on the background thread at load time, then streams small contiguous sample chunks per audio batch through a 4-point Catmull-Rom cubic resampler across any host sample rate from 22.05 kHz to 192 kHz.
  • Allpass-Aligned 0.00 dB Crossover Summation: The four solo bands use cascaded 4th-order Butterworth State Variable Filters paired with matched 2nd-order allpass phase-compensation networks so SUB + LOW + MID + HIGH reconstructs a flat 0.00 dB magnitude response, keeping warm filter states continuously ready behind an 8 ms raised-cosine step-bridge declicker for pop-free switching even on sustained sub-bass.
  • True Bit-Exact Main Bypass: Whenever SAFE is active (or all monitor controls sit at their neutral flat positions), MAIN OUT L/R executes a direct floating-point buffer copy with zero filter coloration and 0 samples of latency.

Join the Touchstone Beta

I'm actively beta testing Touchstone across master-bus reference sessions, 4+ output Control Room interfaces, and headphone mixing setups. If you produce in Reason 10.1+ and want to run the 4-slot BS.1770-4 loudness-matched reference deck, Export-Safe dual-bus routing, 4-band solo matrix, and 40°/60°/80° speaker crossfeed in your own rack, apply below.

// BETA OVERVIEW

Beta Overview

Joining the Touchstone beta gives you early access to the Rack Extension before its release in the Reason Studios Add-on Shop.

  • ⚡
    Direct Account ProvisioningNo license files or manual drops to fiddle with. Beta licenses are linked directly to your Reason Studios account and installed through Reason Companion.
  • 🎛️
    Complete Patch LibraryFull access to all 8 control room, binaural speaker angle (40° / 60° / 80°), band translation, and Export-Safe dual-bus factory repatches (with Reason 13/14 Browser .rsmeta tags).
  • 🔬
    Testing Focus4-slot MP3/WAV/AIFF reference deck & two-pass ITU-R BS.1770-4 loudness matching, Export-Safe dual-bus routing (Main Out 1/2 + Phones Out 3/4), DAW Sync & Cue Loop waveform scrubbing, 24 dB/oct Linkwitz-Riley 4-band solo matrix, 40°/60°/80° headphone crossfeed, rear Control Room CV, and host compatibility across Reason 10.1+ and Reason Rack Plugin.
  • 🤝
    Direct Developer Feedback ChannelDirect communication with the developer for diagnostics, suggestions, and bug reports.
Program StageActive Beta
Format4U Rack Extension
Host SupportReason 10.1 – 14, Reason+, Reason Free
PlatformsmacOS (Apple Silicon & Intel), Windows
// APPLICATION FORM

Tester Application

Fill out your setup details below to join the Touchstone test group.

Select all programs you wish to evaluate. More upcoming releases will appear here as they enter beta testing.
Required: Your exact Reason username (incl. capitalization!) for license provisioning in Companion.